Guide

Tips for every step.

From choosing leather to the last stitch. A few sentences per step, the things that make the difference.

  1. Choose leather and thread

    For the fine leather goods in these patterns, 2.7–5 mm iron spacing is ideal. Your spacing sets the stitch line, the leather and the thread:

    Iron spacingStitch line from edgeLeatherThreadMost common use
    2.7 mm (≈9.4 SPI)3 mm0.8–1.0 mm (2–2.5 oz)0.30–0.40 mmWatch straps, ultra-fine
    3.0 mm (≈8.5 SPI)3 mm1.0–1.2 mm (2.5–3 oz)0.30–0.40 mmSlim wallets
    3.38 mm (≈7.5 SPI)3.5 mm1.2–1.4 mm (3–3.5 oz)0.45–0.55 mmMost wallets
    3.85 mm (≈6.6 SPI)3.5 mm1.2–1.4 mm (3–3.5 oz)0.45–0.55 mmMost wallets
    4.0 mm (≈6.4 SPI)4 mm1.4–1.6 mm (3.5–4 oz)0.60–0.80 mmBags, covers
    5.0 mm (≈5.1 SPI)4 mm1.8–2.2 mm (4.5–5.5 oz)0.80–1.00 mmBelts, sheaths

    Count the layers. Where pockets stack up, many designs reach 3–4 layers. Choose the thinner end of the range so the piece stays slim: four layers of 1.4 mm already make a 5.6 mm (0.22 in) edge.

    Not every panel needs the same thickness. The exterior gives the shape and takes the wear, e.g. exterior 1.2–1.4 mm, pockets and interior 0.8–1.0 mm.

    Scratches: pebbled, embossed or top-coated leathers show them far less than smooth, unfinished veg-tan, which marks easily but develops a patina.

  2. Print and check the scale

    Print at 100% (“actual size”), never “fit to page”. Measure the scale check on the sheet with a ruler before you cut any leather.

  3. Cut

    The grey band around each piece is the trim allowance: cut along its outer line, not the panel line. A sharp knife makes all the difference, so sharpen it regularly.

  4. Glue

    Wherever glue goes on a grain side, scratch it lightly inside the glue margin first (e.g. with a skiving knife), so the glue grips.

    Overlapping pockets: don't let two pockets on the same layer just meet edge to edge, as that gap opens up when the piece bends. Skive the first pocket's 3 mm extension from the grain side and the next pocket's top edge from the flesh side, so they overlap and bond.

  5. Trim the edges

    Layers rarely line up perfectly after gluing and pressing. The trim allowance lets you press firmly, then cut off the excess in one clean pass: a tight, even edge with far less sanding.

  6. Punch the holes

    Punch through all glued layers at once. Round the corners before punching, or keep them square. Rounding afterwards cuts into the hole line.

    Slanted irons at corners: let the slant follow the stitch path; don't point it at the corner. The patterns show the orientation with a small slanted line.

    Steps up or down: the hole in the bottom layer must line up tightly with the one above. The panels are sized so that they do for each spacing.

  7. Stitch

    Never start in the fold area: it takes the most tension and wear. Start in the middle of a short edge.

    With linen thread, reinforce stress points (pocket edges, steps in layers): stitch one hole past the join, go back one hole, then on again, keeping the two threads side by side. Nylon or synthetic thread usually outlasts the leather anyway.

  8. Finish the edges

    Sand the trimmed edge smooth, then finish it the way you like: burnished, painted or simply sealed.

Questions? hello@aptuspatterns.com — Zsombor